- 您现在的位置：买卖IC网 > Sheet目录340 > MAX1574ETB+T (Maxim Integrated)IC LED DRVR WHITE BCKLGT 10TDFN
180mA, 1x/2x, White LED Charge Pump
in 3mm x 3mm TDFN
Detailed Description
The MAX1574 charge pump drives up to three white
LEDs with regulated constant current for uniform inten-
Setting the Output Current
The LED current at full brightness is set by a resistor,
R SET , as follows:
sity. By utilizing adaptive 1x/2x charge-pump modes
and very-low-dropout current regulators, it achieves
180mA output drive capability and high efficiency over
R SET =
0.6V × 393
I LED _
the 1-cell lithium-battery input voltage range. Fixed-fre-
quency switching of 1MHz allows for tiny external com-
ponents, and the regulation scheme is optimized to
ensure low EMI and low input ripple.
1x to 2x Switchover
When V IN is higher than V OUT , the MAX1574 operates in
1x mode and V OUT is pulled up to V IN . The internal cur-
rent regulators regulate the LED current. As V IN drops,
V LED_ eventually falls below the switchover threshold of
130mV, and the MAX1574 starts switching in 2x mode.
When the input voltage rises above V OUT by approxi-
mately 50mV, the MAX1574 switches back to 1x mode.
Soft-Start
The MAX1574 includes soft-start circuitry to limit inrush
current at turn-on. When starting up, the output capacitor
is charged directly from the input with a ramped current
source (with no charge-pump action) until the output volt-
age approaches the input voltage. Once this occurs, the
charge pump determines if 1x or 2x mode is required. In
the case of 1x mode, the soft-start is terminated and nor-
mal operation begins. During the soft-start time, the out-
put current is set to 5% of the maximum set by R SET . In
the case of 2x mode, soft-start operates until the lowest of
LED1 to LED3 reaches regulation. If an overload condi-
tion occurs, soft-start repeats every 2.1ms. If the output is
shorted to ground, the output current is limited by the
MAX1574 switching technique.
EN Dimming Control
When the LEDs are enabled by driving EN high, the
MAX1574 goes through soft-start, bringing the LED cur-
rent up to I LED_ . Dimming is then done by pulsing EN
low (500ns to 500μs pulse width). Each pulse reduces
the LED current by 10%, so after one pulse the LED cur-
rent is 0.9 x I LED . The tenth pulse reduces the current by
5%, so the I LED_ current reduces from 0.1 x I LED_ to 0.05
x I LED . The eleventh pulse sets the LED current back to
I LED_ . Figure 1 shows a timing diagram for EN.
If dimming control is not required, EN works as a simple
on/off control. Drive EN high to enable the LEDs, or
drive EN low for shutdown.
Shutdown Mode
When EN is held low for 2ms or longer, the MAX1574
is shut down and put in a low-current mode. OUT is
internally pulled to GND with 5k ? during shutdown.
Overvoltage Protection
If any LED fails as an open circuit, the output voltage is
limited to about 5V by gating on/off the charge pump.
If any LED_ is floating or grounded, the MAX1574 oper-
ates in the same overvoltage-protection mode. To avoid
overvoltage-protection mode when using fewer than
three LEDs, connect any unused LED_ to IN (Figure 3).
Thermal Shutdown
The MAX1574 includes a thermal-limit circuit that shuts
down the IC at approximately +160°C. The part turns on
after the IC cools by approximately 20°C.
0
INITIAL t HI
≥ 50 μ s
1
2
3
4
5
6
7
8
9
10
11
EN
50%
I LED_
SHDN
t SOFT-START
100%
90%
80%
70%
t LO
500ns TO 500 μ s
60%
t HI
≥ 500ns
40%
30%
20%
10%
5%
100% 90%
t SHDN
2ms (typ)
SHDN
Figure 1. EN Timing Diagram
6
_______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX1575ETE+
IC LED DRVR WHITE BCKLGT 16-TQFN
MAX1576ETG+T
IC LED DRVR WHITE BCKLGT 24-TQFN
MAX1577ZETA+T
IC LED DRIVR BCKLGT FLASH 8-TDFN
MAX1582ETC+T
IC LED DRVR WHITE BCKLGT 12-TQFN
MAX1583ZETB+T
IC LED DRIVR PHOTO FLASH 10-TDFN
MAX1599ETA+T
IC LED DRIVR WHITE BCKLGT 8-TDFN
MAX1614EUA+
IC DVR MOSFET HI-SIDE NCH 8-UMAX
MAX16800ATE/V+
IC LED DRIVR HIGH BRIGHT 16-TQFN
相关代理商/技术参数
MAX1574ETB-T
功能描述:LED照明驱动器 White LED 1x/2x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1574EVKIT
功能描述:LED 照明开发工具 Evaluation Kit for the MAX1574 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
MAX1575ETE
功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE/V+
功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump for Main and Sub-Displays RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE/V+T
功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump for Main and Sub-Displays RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE+
功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE+T
功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1575ETE-T
功能描述:LED照明驱动器 White LED 1x/1.5x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N